Air Equipments And Spares

• Elegant and easy-to-use cabinet
• Large display with 6000 counts and Backlight
• Enhanced current measuring function using an external clamp sensor
• Two detachable holders, flat and wing type
• Accurate reading with True RMS
• Safety Standard IEC 61010-1 CAT IV 300V / CAT III 600V

• Capable of measuring AC and DC currents up to 60A with OPEN CLAMP SENSOR.
• 3400 counts with bargraph display.
• Pocket size and heavy duty design.

Digital Multimeter;
•  Display : 4000 counts.
•  Auto range and manual range selector provided. (with range hold feature)
•  Resistance range provides audible continuity test.
•  Automatically turns power off in about 30 minutes to conserve battery life.
•  Direct current measurement up to 10A AC and DC.
•  With Holster.
Inc. Accessories:  7066A (Test leads), 8919 (Ceramic fuse [10A/600V])× 1, 8923 (Fuse [0.5A/600V])× 1, R6× 2, Instruction Manual

• Temperature measurement, selectable for ºC and ºF
• 6040 counts with Bar Graph display
• MIN/MAX function enables to record min & max value
• REL(relative value) function to indicate the measurement variation

• Large display with 6000 counts and Backlight
• True-RMS
• MIN/MAX function
• Rugged and reliable
• Clamp sensor mode
• IEC 61010-1 CAT IV 300V / CAT III 600V / CAT II 1000V

• Splash / Drop Proof
• 1000V AC / DC
• USB Interface
• Dual Display
• Backlit Display
• Intrinsically Safe
• Beep-JackAudible & Visible Input Warning
• Relative Zero Mode
• PC Interface Capability
• Data Hold
• Ex Rating: Ex ib IIA T4 Gb
• 1A / 1kV (IR10kA)for mA & mA (1000V HRC Fuse)
• 11A / 1kV (IR20kA) for A (1000V HRC Fuse)
• These meters comply to IEC SANS 600790:2000 & IEC SANS 60079-11:1999,
which is applicable for electrical apparatus for explosive gas atmospheres.
Part 0 (general requirements) & part 1 (intrinsic). The approved explosive protection
rating of this equipment is suitable for use in Zone 1 hazardous area.
Group I (coal mines) underground & Group II (surface). DC Voltage Basic Accuracy 0.08%
• 4 Digit 10,000 counts large easy to read Backlight LCD display
• Fast Measurements, 5/sec; Fully Auto-Ranging
• Logic & Line Level Frequency
• Logic Level Duty Cycle Readings & Diode Tester
• Fast Audible Continuity
• Auto Power OffGeneral Specification• Sensing : AC True RMS
• Display :
  9999 Counts : ACV, DCV, Hz & nS
  6000 Counts : mV, mA, mA, A, Ohm & Capacitance
• Update Rate :
  Digital Display : 5 per second nominal;
  41 Segments Bar-graph : 60 per second max
• Low Battery : Below approx 7V
• Operating Temperature : 0°C to 45°C
• Relative Humidity : Max. 80% R.H. for Temperature up to 31°C decreasing linearly to 50% R.H. at 45°C
• Pollution degree : 2
• Storage Temperature : -20°C to 60°C, <80% R.H. (with battery removed)
• Altitude : Operating below 2000m
• Temperature Coefficient : nominal 0.15 x ( specified accuracy)/°C @ (0°C ~ 18°C or 28°C ~ 45°C), or otherwise specified
• Power Consumption : 5mA typical
• APO Timing : Idle for 30 minutes
• APO Consumption : 50mA typical
• Power Supply : Single 9V battery
• Weight : Approx. 635gm with holster
• Dimension : 208(L) x 103(W) x 64.5(H) mm with holster

• Compact in Size, Light in Weight and Simple in Use.
• Double moulding provides comfortable and good feeling in hand.
• Penlight illuminates brightly the point to be measured, even in dark place.
• Backlight LCD is highly visible, even in darkness.
• Unique wrapping mechanism for test lead in the rear side compartment.
• Unique protection mechanism for the test prod for safety.
• All ranges including Ohm range are protected against overload voltage of 600V.

Digital Multimeter:
•  Capable of measuring AC and DC currents up to 120A with OPEN CLAMP SENSOR.
•  3400 counts with bargraph display.
•  True RMS
•  Pocket size and heavy duty design.
Inc. Accessories:  R03 (DC 1.5V) × 2, Instruction Manual"

Sensing : Average sensing
• Display : 3-3/4 digits 4000 counts large easy to read LCD display
• Update Rate : 3 per second nominal
• Polarity : Automatic
• Operating Temperature : 0 °C to 40 °C
• Relative Humidity : Maximum 80% R. H. For temperature upto 31 °C decreasing linearly to 50% Relative Humidity at 40 °C
• Altitude : Operating below 2000m
• Pollution degree : 2
• Storage Temperature : -20 °C to 60 °C, < 80% R.H. (With battery removed)
• Temperature Coefficient : nominal 0.15 x (specified accuracy) / °C @ (0 °C -18 °C or 28 °C-40 °C),
or otherwise specified
• Low Battery : Below approx 2.4V
• Power supply : Standard 1.5V AAA Battery x 2.
• Power Consumption : 3.2mA typical
• Sleep mode Timing : Idle for 30 minutes
• Sleep mode Consumption : 300 μ A typical
• Dimension : 186(L) x 87(W) x 35.5(H) mm ; 198(L) x 97(W) x 55 (H) mm with Holster.
• Weight : Approx. 296 gms; 396gm with holster.Features
• Basic Accuracy : 0.5% DCV
• 25ms Max Hold
• Fully Autoranging
• Data Hold
• Relative Zero Mode
• Jack Beep audible warning against improper plug in
• Diode Test
• Fast audible Continuity Test
• Fire retarded case
• Splash proof construction.
• Auto power off

• 3½ Digits
• 2000 Counts
• Manual Ranging
• DC Voltage upto 1000V
• AC Voltage upto 750V
• DC Current upto 10A
• AC Current upto 10A
• Resistance upto 20MΩ
• Diode Test
• hFE Test (Transistor Test)
• Continuity Test (LED, Buzzer & EF Strength)
• NCV (LED, Buzzer & EF Strength)
• LCD with Backlight
• Data Hold
• Auto Power Off
• Holster with Magnet
• Torch Light
• Test Lead Gripper
• Low Battery Indication

 

Special Feautres :
• Record Max, MIN, MAX-MIN readings.
• Crest (Instantaneous Pead Hold) MAX, MIN, MAX-MIN readings.
• Relative zero mode.
• 500,000 counts high resolution stable reading mode. Backlighted display
• dBm readings.
• T1-T2 differential temperature reading s
• %4-20 mA loop current readings.
• High noise rejection filtered Line Level Frequency mode
• Line Level Frequency mode with 4 Trigger Levels.
• HBC Fuse Protection

Feautres :
• DC Voltage Basic Accuracy 0.02%
• Fully Autoranging
• Backlighted display.
• T1-T2 differential Temperature readings.
• Fast Data Measurement 5/sec
• Data Hold, Diode Test & Duty Cycle
• Audible & Visible input warning.
• Auto Power Off .

General Specifications
• Sensing : AC, AC + DC True RMS;
  Frequency Bandwidth 100kHz (V) & 10kHz (A)
• Display :
  4-4/5 digits 50,000 counts. Selectable stable mode
  5-4/5 digits 500,000 counts for DC voltage,
  6 digits 999,999 counts for Hz
• Polarity : Automatic
• Update Rate :
  4-4/5 digits fast mode : 5 per second nominal;
  5-4/5 digits stable mode : 1.25 per second nominal;
  42 Segments Bar graph : 60 per second max.
• Low Battery : Below approx. 7V
• Operating Temperature : -20°C to 60°C
• Relative Humidity : Maximum 90% R.H. For Temperature upto 31C decreasing linearly to 50% R.H. at 60C
• Pollution Degree : 2
• Storage Temperature : -20°C to 60°C, < 80% R.H. (With battery removed)
• Altitude : Operating below 2000m
• Temperature : Nominal 0.1 x (specified accuracy) / °C @ (0°C - 18°C or 28°C - 40°C), or otherwise specified.
• Power Supply : Single Alkaline 9V battery.
• Power Consumption : 5mA typical
• APO timing : Idle for 4.5 minutes
• APO Consumption : 20µA
• Dimension :
  186(L) mm x 87(W) mm x 35.5(H) mm;
  198(L) mm x 97(W) mm x 55(H) mm with Holster
• Weight : 390 gm, 500 gm with Holster

The Metravi ERT-1501 is an electronic, digital, earth resistance tester and a direct replacement or the conventional hand generator type tester for 0 – 10 / 100 / 1000Ω, and features 4 Terminals with a Testing Kit and Cables in a hard carrying case. The device measures Earthing used in electrical equipment as well as Ground Resistivity. It can also be used for measurements of the other low regular and liquid resistances, as well as AC Voltage, DC Voltage and Resistance. The tester finds wide application for testing earthing installations in industries like Power, Telecommunications and Electrical Traction Systems.

The Metravi ERT-1502 is an electronic, digital, earth resistance tester and a direct replacement or the conventional hand generator type tester for 0 – 20 / 200 / 2000Ω, and features 4 Terminals with a Testing Kit and Cables in a hard carrying case.

The Metravi XB-33A is a 6000 Counts T-RMS Digital multimeter with a backlit LCD display. In case if you don’t know whether two points are short, or have voltage or linear resistance, no need to worry. Just connect this multimeter and the instrument will detect automatically. This auto-ranging meter can measure AC T-RMS Voltage and Current, DC Current / Voltage, Frequency, Resistance, Capacitance & Temperature. It also has Diode and Continuity Test and Non-contact Voltage Detection, along with overload protection to against incorrect connections.

Ability to measure wind speed in feet per minute or meters per second Data capture using one button and the ability to average multiple readings Min and Max alarm setting to alert the user when limits have been met Durable over mold housing to protect the unit from drops 1 M extension of sensor from display to ensure air flow is captured in hard to reach locations

Measure in lux or foot-candles, with one button to switch between display options Measuring range up to 20,000 lux or foot candles Data hold to freeze reading on the digital display Min/max ability to show high and low readings Auto power off to save battery life Includes protective sensor cap

The Metravi XB-33CF is a pocket-sized 3 5/6-digits, 6000 counts, auto-ranging multimeter. It has stable performance, high precision, high reliability, clear reading, with overload protection. With AAA 1.5V battery the instrument uses a large-screen LCD display, boost power supply, even in the 2.3V low battery, it can guarantee high backlight brightness, the meter is easy to carry, has a vast number of usages, the backlight can be automatically turned off after 15 seconds. This instrument can be used to measure DC voltage, AC voltage, DC current, AC current, Resistance, Capacitance, Temperature, Frequency, Diode, Continuity Test, Non Contact Voltage detection, true RMS measurement and other parameters. It is an ideal tool for the laboratory, factory, radio enthusiasts and families

3-5/6 digits 6000 Counts TRMS Digital Multimeter with NonContact Voltage Measure

Meko Analog Multimeters are known for their precision and durability. They can measure various electrical parameters like voltage, current, and resistance, which makes them versatile tools for both professionals and hobbyists. The analog design offers a visual representation of measurements with a needle moving across a scale, which some users find more intuitive than digital readouts.